z/OS Service Package: X2026264


SMP/E SYSMOD:
Component:
Operating System:
Publish Date:
APAR & Description:

RS35006
FileKit
z/OS
2026/11/12

IQ005610, IQ005613, IQ005618, IQ005619, IQ005620, IQ005636, IQ005643, IQ005647, IQ005652, IQ005677:

The following corrections and enhancements have been applied to the FSU (File Search, Update, Copy) and FCOPY (File Copy) utilities:

  1. Support MKDIR (MD) option, used when copying to a ZFS/HFS file path from another ZFS/HFS file directory. If necessary, the copy will create new sub-directories in the destination directories with names that match the selected input directories.

  2. Correct RECURSE option so that files in source ZFS/HFS sub-directories are copied to sub-directories of the same name at the target ZFS/HFS location.

    MKDIR should also be specified if the target directories do not already exist.

  3. Support ARCHIVE (ARC) option, used when copying to a ZFS/HFS file path. If the target file already exists, then before the copy occurs it will first be renamed with a name in the following format:

       %fn%-yyyymmdd-hhmmss.%ext%

    Where %fn% is the original file name, and %ext% is the original file extension.

  4. Support TIMECHK (TC) option, used when copying to and from ZFS/HFS file paths or library members that have a "last changed" timestamp. TIMECHK will compare the source and target last changed timestamps and only perform the copy if the source file timestamp is later than that of the target file.

    No timestamp check will occur for target files that do not have a last changed timestamp.

  5. Give an error if copy to a library member fails due to failure to write the directory record. e.g. no free PDS directory blocks.

  6. Correct loop that occurred in the MVS CHECK macro following a member I/O error during a library copy operation.

  7. Correct possible 0C4 (and other errors) caused by unexpected positioning of FSU primary command keywords.

  8. Correct loss of the first few data characters on each record when a ZFS/HFS RECFM=V file is copied to a data set/library member. The number of characters lost is equal to the size of the length field specified for the ZFS/HFS RECFM=V file.

  9. Correct possible loop that occurred in FSU with a CHANGE ALL operand, where an attempt to change a search string to a longer replace string fails. For example, when the replace string would cause the record text to exceed specified bounds or current record length.



IQ005615, IQ005623:

The following corrections and enhancements have been applied to the COMPFILE (File Compare) utility:
  1. Support NOHEX option for LIST=TEXT output. This option will suppress output of the vertical (up/down) display of hex values for text containing unprintable characters.

  2. For LIST=FMT output, suppress generation of an SDO report mapping object when NOREPORT is specified.



IQ005611, IQ005612, IQ005625, IQ005633, IQ005640, IQ005646, IQ005665, IQ005666, IQ005667, IQ005669, IQ005672, IQ005676, IQ005680, IQ005681, IQ005682:

The following corrections and enhancements have been applied to the REPORT utility:

  1. Introduce LIBRARY and CLD parameters on INPUT specification to support multiple member input from a library DSN or concatenation of libraries.

    For example, to input member "T015" and all members with names beginning "T119" in library "CBL.TEST1":

        INPUT:
             CBL.TEST1(T119*,T015)             \
             USING   SDO   CBL.FKIT.SDO(TEST)  \
             LIBRARY
    

    To input the first occurance of each member with name beginning "T" in a library concatenation search path "CBL.TEST1, CBL.TEST2":

        INPUT:
             CBL.TEST1, CBL.TEST2(T*)          \
             USING   SDO   CBL.FKIT.SDO(TEST)  \
             CLD
    

  2. Support multiple, concurrent report output with different report formats (JSON, XML, CSV and PRINT) simultaneously. Previously, to create the same report output in different formats, the job would have to be executed repeatedly, once for each required report format.

  3. Support extension to built-in function, BYPASS().

        BYPASS([ [RECord] , [RESet] ])

    where:
        RECORD
    For segmented record input (e.g. SMF records), bypass the current segment and all remaining segments in the current record. By default, only the current segment is bypassed.
        RESET

    If bypass has been triggered, then reset the field values that have been set following input of the current record/segment, to null or blank values. By default, these field values are reset to their original values as assigned before input of the current record/segment.

  4. Support new built-in function, SKIP() which will bypass the current record/segment but, unlike BYPASS(), will not attempt to reset field values set following input of the current record/segment.

        SKIP( [RECord] )

    where:
        RECORD
    For segmented record input (e.g. SMF records), bypass the current segment and all remaining segments in the current record. By default, only the current segment is bypassed.

  5. Support new REPORT definition section INCLUDE:

    The contents of data sets and/or library members named in this section will be included as part of the REPORT definition input.

    The contents of these files will be inserted immediately following their specification in the INCLUDE: section.

    For example:

        INCLUDE:
           CBL.FKIT.RPT(STD030)
           CBL.FKIT.RPT(STD041)
    

    Included definition control syntax may itself specify an INCLUDE: section and so nested layers of included control statements may exist. To avoid possible loops of nested included files, an error will occur if the same file is included more than once.

  6. Correct situation where a BREAK section is specified without a SORT section and input SMF records of different record types are to be processed. This can lead to a missing report break due to the break key field being unset.



IQ005651:

The following corrections and enhancements have been applied to DB2 utilities:
  1. Correct 0C4 that may occur on attempting to connect to a DB2 sub-system name (SSN) that does not yet exist.



IQ005638, IQ005650, IQ005657:

The following corrections and enhancements have been applied to the Text Editor:

  1. Correct 0C4 that may occur when RCHANGE is executed in a text edit view of a file which has a smaller LRECL than that of a file in a different text edit view in which the last CHANGE operation was performed.

  2. Enhance the BLOCK Text-Edit (CBLE) REXX macro so that it will use values set to FILE level environment variables "BLOCK_MAJ" and "BLOCK_MIN" as the default major and minor target strings respectively.

    BLOCK is usually assigned by the user to a PF Key or keyboard macro to scroll to the next major or minor heading in the displayed text.

    By default, major heading lines are identified as containing "***" or "===". Minor heading lines are identified as containing "**" or "==".

    This is equivalent to setting environment variables BLOCK_MAJ and BLOCK_MIN as follows:

        editv setlf BLOCK_MAJ  /*** /|/===/
        editv setlf BLOCK_MIN   /** /|/==/
    

  3. Enhance the SV Text-Edit (CBLE) REXX macro so that it will bypass level and timestamp header update on save if the library or data set DSN is one set to the FILE level environment variable "SV#Exceptions".

    For example, to bypass header update when using SV to save changes to members edited from libraries "CBL.SS.LISTMAST" and "CBL.VV.LISTMAST", set SV#Exceptions environment variable as follows:

        EQU SV#Exceptions CBL.SS.LISTMAST CBL.VV.LISTMAST
    



IQ005622, IQ005635, IQ005642, IQ005648, IQ005656, IQ005675:

The following corrections and enhancements have been applied to the Data Editor:
  1. Increase maximum prefix area width to 10 digits.
  2. Correct 0C4 that may occur on display of a record containing a long horizontal hex field with comma and blank punctuation (i.e. fields of record types HEX, VARHEX, HEXVAR, BIN or VARBIN).

  3. Correct INPUT primary command error where input of a value to a BINTEGER field of length greater than 1-bit simply inputs a zero (0) value.

  4. For IMS database browse only, correct internal error message that occurred when scrolling. "DOWN MAX" and repeated "UP" commands eventually gave this internal error.

  5. Support DSN macro to extract the dataset name contents of the focus field within a formatted record.



IQ005617, IQ005626, IQ005631:

The following corrections and enhancements have been applied to FILEIO functionality:

  1. Support generic file input (like FSU or DIRDATA for SELCOPY).

                                        +-----------+
                                        v           |
      >>- FILEIO fid OPENREAD -- MASK --+-----------+----><
                     OPENUPD            |           |
                                        +- CASEIGN -+
                                        |           |
                                        +- SUBDIR --+
    

    Where fid is a dataset, library member or ZFS/HFS file path containing wild card characters as follows:
        "*" (asterisk)
    represents any character string of any or null length.
        "%" (percent)
    represents any character (i.e. length 1)

    "CASEIGN" and "SUBDIR" apply to input of ZFS/HFS file paths only.

    CASEIGN indicates that the character case in fid should be ignored when matching file path names.

    SUBDIR indicates that all matching file names in all sub-directories of the directory specified in the file path will be read.

    For example:

         fileio /mnt/xn1/z/cg/*.kex openr name MSK mask \
                                            caseign subdir
    
         fileio CBL.SMF.GDG.*       openr name MSK mask
    
         fileio CBL.CBLI*.JCL(A*)   openr name MSK mask
    

    In the above, the name "MSK" is assigned to the input stream.

    During input processing, return codes are set as follows:
        RC=2
    End of member (same as for normal LIBRARY or CLD input).
        RC=4
    End of dataset, HFS file or library.
        RC=6
    End of MASK input.

  2. Support new OPTION FILEID to set REXX variable name.1.FILEID to the current input fileid for the named mask.

    For example, if MSK is the name of the input stream, the following will set MSK.1.FILEID to the current fileid:

        fileio MSK option FILEID

  3. Support setting member timestamp and other library directory member information.

    Note: SETDIRINFO TIMESTAMP is also supported for ZFS/HFS file paths.

                                 +---------------------+
                                 v                     |
      >>- FILEIO xxx SETDIRINFO -+---------------------+-><
                                 |                     |
                                 + TIMESTAMP date time +
                                 |                     |
                                 + USERID username  ---+
                                 |                     |
                                 + INISIZE nrecs ------+
                                 |                     |
                                 + CURSIZE nrecs ------+
    

    For example:

      fileio NBJ.ASM openupdate
      fileio NBJ.ASM member VCATALI
      fileio NBJ.ASM setdirinfo timestamp 2025/05/14 16:36:01
      fileio NBJ.ASM member VCATBLD
      fileio NBJ.ASM setdirinfo cursize 22 inisize 11
    

  4. Correct bug which bypasses the update of the current record when UPDATE, UPDATEV or UPDATEX is used and the supplied record is shorter than the original. The updated record will now contain the new data plus the remainder of the original record data.



IQ005616, IQ005624, IQ005627, IQ005628, IQ005629, IQ005630, IQ005632, IQ005634, IQ005639, IQ005645, IQ005653, IQ005659, IQ005662, IQ005664:

The following general corrections and enhancements have been applied to FileKIt:

  1. Enhance Library List (LL) output so that the member "Last Changed" timestamp includes the number of seconds value.

  2. Correct RENAME for a VSAM object so that it no longer prompts the user for a volser id. VSAM rename is a catalog update and volume serial id is not required.

  3. Correct concatenated library directory (CLD) member list whereby a directory block was being bypassed if its first entry is a member with a null name.

  4. Additional ONLY primary command included in LLX output.

  5. Correct SMFB bug introduced by IQ005587 for basic display of SMF records with FIND operand to filter records, resulting in all records being excluded.

  6. Correct RANDOMIZER storage leak when a chain (e.g PATTERN) is used.

  7. Correct FILEKITB (batch) execution attempt to open a I/O progress window.

  8. Prevent FILEKITB (batch) execution error which occurred when no user INI file exists.

  9. Update ERASE with operand "-Q" so that all messages are suppressed.

  10. Minor alterations to SELCDBJ macro which prepares JCL for SELCOPY Debug run(s).

  11. Correct potential loop in output messages.

  12. Support DSNEWNAM for generic DSN RENAME.